Are You Responsible For A Fiat Panda Key Fob Replacement Budget? 12 Ways To Spend Your Money
Reasons Your Fiat 500 Key Fob Won't Work
A key fob from Fiat 500 allows you to easily open doors and start your car. However, there are a variety of reasons the fob could stop working. These include a dead coin battery damage to the receiver module, issues, or interference.
This listing is for a NEW replacement Fiat Flip Key Remote that looks like the Ilco brand. It has to be professionally programmed (click here to search for local locksmiths in the automotive industry). Includes lock, unlock and trunk buttons.
Dead Coin Battery
The most common reason the 500 key fob won't work is a dead battery. Modern key fobs have a limited operating range and must be within a few feet of the vehicle to operate. If you're far away from your vehicle and you press the key fob button, the car won't respond, and will display a "Key Fob Not Detected" message in the instrument cluster.
If this occurs If this happens, replace the battery in the coin-cell (Part Number CR2032) by a new one of a trusted brand such as Panasonic Duracell or Energizer. You can find them at your local hardware store or on the internet.
After you've replaced the battery of your coin cell you can test it by standing in front of your Fiat 500 and pressing the buttons. The car will flash its parking lights and the key fob should be able to operate the lock and unlock buttons.
If the fob's remote doesn't work after replacing the battery, it may be damaged by water, which prevents it from communicating with the receiver module inside your car. Water damage can occur in a variety of ways, from an accidental splash to submerging the fob in salt water at the beach. If you suspect your fob was exposed to water, you can try placing it in a dry rice bag to draw the moisture back out. If fiat 500 replacement key near me thekeylab.co.uk doesn't work, you will need to have your fob replaced by an auto locksmith or dealer.
Water Damage
The fob does have rubber seals to keep water from the electronic chip inside, submerging it in the ocean or washing it in a machine could cause water damage. Saltwater is particularly dangerous to the circuit board of the fob and can cause it to short out and eventually die. The fob getting wet is not a good idea but if you drop it in a cup of water or forget to take it out of your pocket before you run the washer do not give up hope.
First, remove the battery. Before replacing the battery, clean the electronic chip using isopropyl, or a similar product. Test the fob next to verify if it's functioning. If the key still doesn't work, it might need to be reprogrammed. This is usually done by a dealer or professional auto locksmith.
If the key is older and has never been programmed to your car it is likely to need to be replaced completely. A professional locksmith in the automotive industry will be able to complete this process. The locksmith will need the key to be cut to match your vehicle's ignition. They'll also need to program the fob into your vehicle's system. This is a quick and cost-effective procedure that can be completed within the same day.
Receiver Module Issues
The 500 key fob could not work because it's out of range. The remote typically has an operating range of 30 feet or less, and if it's too far from your vehicle, it will not respond to your commands. This can be easily fixed by moving closer to your vehicle until it starts responding.
If you've replaced your coin battery (commonly called a "button" or "watch") and your fob still won't work It could be because of an internal circuit board issue. In most cases, reprogramming the fob will solve the issue. You can find the instructions for the majority of vehicles on YouTube or in the owner's guide.
You may need to replace the metal clips that keep the battery of your coin in place. If they loose tension it could hinder the coin battery from sitting properly and could result in the malfunction of your remote.
In rare cases, the fob may become disconnected from your vehicle due to software problems or hardware issues. This issue can be fixed by visiting your local dealer or auto-locksmith to reprogram your key fob. In some cases, they may need to reinstall the program in your body control module, too.
Interference
In addition to a dead coin battery The key fob may not be receiving or transmitting the signal due to interference. This could occur if the key fob is near an electronic radio transmitter (cell phones and radar detectors) or any other source of electromagnetic radiation. Other reasons the key fob may not function could be due to a weak connection to the buttons or damage to the internal chip, or water damage.
If the key fob been unable to function for a while without notice and you've tried everything you can do at home to resolve it e.g. replacing the battery, reprogramming, and using the spare key fob, you might have a defective receiver module on your 500. The receiver module is located under the dash and receives the radio frequency signals from the key fob. It converts them to electronic commands that the vehicle interprets.
Luckily, there is an easy way to reset all on-board systems in your 500 device, including the key fob. Disconnect the battery for 15 minutes, removing first the negative cable and then the positive cable. Then, reconnect the battery. This will clear out any remaining electrical charge and restart the car's computers, which can help you the key fob to function again. If the issue continues, you should speak with an expert technician. They will be able to diagnose the exact cause of your problems.
